BISON EPOXY 5 MINUTES 24ML
DESCRIPTION
Application
Mixture ratio: 1:1
Coverage: 1 ml = approx 1 cm² at a film thickness of 1 mm
Directions for use:
Remove the spatula from the side of the double syringe, and the closure cap
from the handle. Break the seal of the double syringe. Press out an equal
amount of both components onto the enclosed mixing tray. Mix these two
equal parts well with the synthetic spatula. Apply the mixture, which at room
temperature (+20°C) remains tool able for about 5 minutes, as a thin layer on
one of the two materials. Assemble the material and keep it in place for 20
minutes. Be careful not to move the parts before the adhesive has cured. After
use, clean the nozzle with a cloth and place the special cap in the handle on the
double syringe. Resin and hardener must not come into contact with each other
unless for usage.
Pot life: 5 minutes
Stains/residue: Remove wet stains immediately with warm water and soap.
Cured adhesive residue can only be removed mechanically.
Advice: Some types of synthetics can not be joined such as polyethylene and
polypropylene. This can be tested by holding a glowing copper wire against the
synthetics. Does it smell of wax? Then you can not bond it.
Use a piece of adhesive tape in order to keep the parts in place while the
the adhesive is curing.
Points of attention: After use close well (note: always place back the cap
in the same way, due to the bonding of the cap to the double syringe). For
optimum performance, it is important to create a larger amount of adhesive and
mix it very well. Curing time depends on temperature. The adhesive does not
cure below +5°C.
Cure times*
Handling time: approx. 20 minutes
Drying/Curing time: approx. 1 hour. Curing takes longer at lower
temperatures, and shorter at higher temperatures.
* Curing time may vary depending on a.o. surface, product quantity used humidity level and ambient
temperature.
Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +100°C
Chemicals resistance: Good
Filling capacity: Good
Technical specifications
Chemical base: Resin: epoxy resin. Hardener: modified amide
Colour: Transparent
Viscosity: approx. Liquid
Solid matter: approx. 100 %
Density: approx. 1.16 g/cm³
Storage conditions
At least 24 months after the date of manufacture. Limited shelf life after opening.
Store cool, frost-free, upstanding (nozzle upwards) and tightly closed.
Product description
Crystal clear fast dual-component epoxy adhesive.
Field of application
Ideal for fast, strong and invisible repair of many materials, such as pottery,
porcelain, glass, leather, wood, stone, metal, ceramics. Both with themselves
and in combination. Not suitable for Polyethylene (PE), polypropylene (PP),
PTFE and silicone rubber.
Properties
· Fast
· Crystal clear
· Super-strong
· Universal, suitable for many materials
· Resistant to temperatures
· Filling
· Water-resistant
· Chemical resistant
· Paintable
Preparation
Working conditions: Only apply at temperatures between +5°C and +35°C.
Product cures by mixing the resin and hardener.
Personal safety: Preferably wear gloves.
Surface requirements: The materials to be bonded must be dry, clean, free of
dust and grease.
Preliminary surface treatment: Degrease parts to be bonded with acetone.
Roughen smooth surfaces (sandpaper).
Tools: Mix the components in the double-syringe by means of the supplied
mixing bowl and spatula.
BISON EPOXY 5 MINUTES 24ML
DESCRIPTION
Application
Mixture ratio: 1:1
Coverage: 1 ml = approx 1 cm² at a film thickness of 1 mm
Directions for use:
Remove the spatula from the side of the double syringe, and the closure cap
from the handle. Break the seal of the double syringe. Press out an equal
amount of both components onto the enclosed mixing tray. Mix these two
equal parts well with the synthetic spatula. Apply the mixture, which at room
temperature (+20°C) remains tool able for about 5 minutes, as a thin layer on
one of the two materials. Assemble the material and keep it in place for 20
minutes. Be careful not to move the parts before the adhesive has cured. After
use, clean the nozzle with a cloth and place the special cap in the handle on the
double syringe. Resin and hardener must not come into contact with each other
unless for usage.
Pot life: 5 minutes
Stains/residue: Remove wet stains immediately with warm water and soap.
Cured adhesive residue can only be removed mechanically.
Advice: Some types of synthetics can not be joined such as polyethylene and
polypropylene. This can be tested by holding a glowing copper wire against the
synthetics. Does it smell of wax? Then you can not bond it.
Use a piece of adhesive tape in order to keep the parts in place while the
the adhesive is curing.
Points of attention: After use close well (note: always place back the cap
in the same way, due to the bonding of the cap to the double syringe). For
optimum performance, it is important to create a larger amount of adhesive and
mix it very well. Curing time depends on temperature. The adhesive does not
cure below +5°C.
Cure times*
Handling time: approx. 20 minutes
Drying/Curing time: approx. 1 hour. Curing takes longer at lower
temperatures, and shorter at higher temperatures.
* Curing time may vary depending on a.o. surface, product quantity used humidity level and ambient
temperature.
Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +100°C
Chemicals resistance: Good
Filling capacity: Good
Technical specifications
Chemical base: Resin: epoxy resin. Hardener: modified amide
Colour: Transparent
Viscosity: approx. Liquid
Solid matter: approx. 100 %
Density: approx. 1.16 g/cm³
Storage conditions
At least 24 months after the date of manufacture. Limited shelf life after opening.
Store cool, frost-free, upstanding (nozzle upwards) and tightly closed.
Product description
Crystal clear fast dual-component epoxy adhesive.
Field of application
Ideal for fast, strong and invisible repair of many materials, such as pottery,
porcelain, glass, leather, wood, stone, metal, ceramics. Both with themselves
and in combination. Not suitable for Polyethylene (PE), polypropylene (PP),
PTFE and silicone rubber.
Properties
· Fast
· Crystal clear
· Super-strong
· Universal, suitable for many materials
· Resistant to temperatures
· Filling
· Water-resistant
· Chemical resistant
· Paintable
Preparation
Working conditions: Only apply at temperatures between +5°C and +35°C.
Product cures by mixing the resin and hardener.
Personal safety: Preferably wear gloves.
Surface requirements: The materials to be bonded must be dry, clean, free of
dust and grease.
Preliminary surface treatment: Degrease parts to be bonded with acetone.
Roughen smooth surfaces (sandpaper).
Tools: Mix the components in the double-syringe by means of the supplied
mixing bowl and spatula.
